The tapered barrel on these bushings is split on both sides, permitting them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for work with with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it in to the sprocket or pulley.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and may be purchased on a single page as the pulley you will need. For apply with 5/8” shaft sizes. Includes set screws. Further Features: Made of Steel For apply with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque potential from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are utilized on sheaves, pulleys, sprockets and gear belt pulleys. The split tapered bushing alleviates the necessity to have an element bored to size, ideally lowering readily available requirements and allowing for alterations in shaft size if important. The barrel of the split tapered bushing is split in two locations and is definitely keyed to the shaft. The barrel OD can be keyed to the travel component aswell. The advantage of the split tapered bushing could it be will hold, regardless if the fasteners become loose. Split tapered bushings happen to be interchangeable between manufacturers.

Taper bushing are widely used together with sprockets, v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are made of high quality engineered resources with great tolerance. The characteristic is easy to work with and needs no extra alteration. These bushings can go well with almost a myriad of assemblies and sizes. They will be the best choice in design for mechanical connections.
To complete designations put bore size. For example: PD1215X16MM designates a 1215 taper bushing with a 16mm bore.
No costly re-boring: full range of both metric and imperial obtainable.
Standard range suits up to 125mm/5″ shafts & Hub diameter required is determined by the application.
Complete short reach range offered, for compact light and portable assemblies & Clean, Compact Style.
Simple installation and removal.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and may be purchased on a single page as the pulley you will need.
For use with 1 3/16” shaft sizes.
Includes 2 set screws.

Additional Features:
Made of Steel
For use with cast iron bushed bore pulley
This U1 Bushing with 5-1/2″ bore is a high-quality precision product that’s built for strength and strength. U1 bushings are used in an extensively wide selection of applications, which include; sprockets, shaves, pulleys, gears, and much more, we also offer most of these goods. What units this bushing apart is the high-quality steel engineering along with precise manufacturing and high quality control; this means that you always get a premium quality regular product. What really units us in addition to the other guys is our experienced expert workers and our company-wide target of customer satisfaction.
1. Be sure the tapered cone floors of the bushing and the inside of the driven merchandise are clean and free of anti-seize lubricants.
2. Place the bushing in sprocket or other component type that accepts the bushing.
3. Place cap screws loosely in pull-up holes. The bushing continues to be loose to assure sliding fit on shaft.
4. With important on shaft, slide the sprocket or other component type to the required posture on the shaft. Be sure to leave the heads of the cap screws attainable.
5. Align the sprocket or part type, tighten the screws on the other hand and progressively until they will be pulled up tight. Do not use extensions on the wrench handles , nor permit the sprocket or portion to be drawn i connection with flange of bushing. At this stage there should be a gap between the bushing flange and sprocket, make certain this gap will not close.
Double split barrel ensures concentricity
Grips the shaft with confident clamp fit
High torque carrying capacity
Permits blind assembly
Load not carried or tied to mounting screws
External key of all sizes for positive drive and increased torque carrying capabilities
Double-split barrel for great Split Taper Bushing china clamping
Solid flange to keep up concentric bores
Available in inch, metric, and spline bores. Bore range between 3/8″ to 10″
Solid Flange & Double Split Barrel – Assures better concentricity to the shaft.
Key to Key Drive – With keys in both the shaft and item to provide the strongest possible drive.
3/4″ per Foot Taper on Barrel – Personal locking taper supplies the highest degree of mechanical locking item to product.
The tapered barrel on these bushings is split on both sides, permitting them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for make use of with split-tapered sprockets and pulleys of the same bushing design. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and can be purchased on the same page as the pulley you need. For apply with 5/8” shaft sizes. Includes set screws. Extra Features: Made of Steel For employ with cast iron bushed bore pulley
Our stock steel Split Taper bushings feature wrench torque capability from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the necessity to have a component bored to size, ideally lowering readily available requirements and enabling alterations in shaft size if necessary. The barrel of the split tapered bushing is certainly split in two locations and is certainly keyed to the shaft. The barrel OD is also keyed to the drive component aswell. The good thing about the split tapered bushing could it be will hold, whether or not the fasteners become loose. Split tapered bushings are interchangeable between manufacturers.