The EP Series Helical Bevel Reducer provides unmatched performance, durability, and design flexibility. This unit offers torque capacities up to 20,000 Nm (14,750 ft lbs).
The cat4CAD software allows simple interactive product selection of the entire gearbox and gear-electric motor system. Cat4CAD supports you in choosing and configuring these products, provides you the opportunity to print out intensive technical data sheets, and generates complete 2D drawings and 3D models for direct download.
11 sizes
Input power capacities from 0.16 to 120 HP
Gear ratios from 5:1 to 8900:1
Torque capacities to 20,000 Nm
Inverter duty class F insulated motor windings
Class 12 Helical and Spiral Bevel Gears: Provides higher efficiencies and better torques in smaller sizes.
Multiple Input Options: Essential gear motors, in . or metric shafts, NEMA, IEC, and servo adapters provide unmatched drive versatility.
Multiple Output Choices: Hollow bores and shrink disks for shaft installation, inch and metric output shafts, mounting pilots and flanges provide an array of design solutions.
UNIBLOCK Housing: For optimum rigidity, universal mounting on five sides or via a torque arm.
Worldwide Engine: Multiple leads and windings for globally multi volt/Hz requirements plus modular design to simply accept brakes, encoders or pressured cooling.
High efficiency electric motor design available
Innovative self-locking, self-aligning taper shaft electric motor connection
Gearbox supplied factory filled with synthetic oil
Corrosion and shock resistant cast iron housing
High efficiency helical-bevel gears. 98% per stage
Normally closed breather with multiple places (Optional OtN2000)
Double lip seals upon heat treated, plunge floor shafts
Shaft mounting choices include tapered bushings designs
This is a comprehensive offering of energy-efficient, right angle helical bevel enclosed gearing. It is available as gearmotors and a number of reducers with torque capacities up to 119,000 inch pounds. Housing designs include footed, face and flanged configurations. Gearmotors are available in three stage high efficiency styles through 50 HP and single phase to 5 HP. We offer a selection of input and output shaft options. Additionally, you will see fixed and variable rate motors and range of ratios obtainable in this product offering.
Features
Accommodates input power from ¼ Hp to 75Hp
Torque ratings up to 119,489 in-lbs
Decrease ratios up to 7,500:1
Helical – bevel – helical gear train offers affordable high and low speed solutions
Up to 94% efficient
Four input options available for all units
Two output flange choices – B5 and B14
Multiple output shaft interfaces
Critical dimensions interchangeable with major competitors
Modifications / Accessories
Integral Gearmotor
Clamp Collar C-Face Input
Solid Shaft Input
3-Piece Coupled C-Face Input
CEMA Screw Conveyor Adapter
EZ Kleen Washdown Package
XT Output Seals
Backstop
DURABLE Output Bearings
Inch or Metric Dimensions
Common Applications
Troughing Belt Conveyors
Slider Bed Conveyors
Mixer Drives
Screw Conveyors
Bucket Elevators
General Industrial Machinery
Common Industries
Aggregate and Cement
Air Handling
Chemical, Oil, and Gas
Food, Beverage, and Pharmaceutical
Paper and Forest
Unit and Baggage Handling
Water and Wastewater
As per the developing and varying demands of customers, you can expect a wide selection of Helical Bevel Equipment Reducers. The technological articles of our products allows for an extraordinary functionality/lifespan ratio. The highly versatile Helical Bevel Gear Reducers we offer are successfully used in a multitude of industrial and civil applications. They are B-Series units that offer excellent affordability and result torque/weight ratio, especially due to the fact they need very limited servicing. Besides these, our products are available in cast iron (sizes 063 to 163) or light weight aluminum (sizes A42 to A73) casing.
Features:
Sizes: 060-080-100-125-140-150-160
Available versions: B-fitted for electric motor coupling, IB with input shaft, CB with small motor, PB-fitted for motor coupling with flexible joint
Casing with ft FC, flange SC and common UC
Switch on to 90 kW
Gears hardened and tempered with shaved or surface profile
Gearing with 3 decrease stages
Gleason spiral bevel equipment pairs with run-in profile, mounted as second reduction stage for a higher resistance
Reduction ratios between 5, 71 and 187, 24
Torque max 13.000 Nm and admissible radial loads max 80.000 N
High-strength casings optimized with FEM evaluation and input and result flanges of grey cast-iron G200 to make sure best level performances and high reliability
Load capacity calculated and verified according to ISO 6336 and AGMA 2001
Painted with RAL 5010 blue epoxy-polyester powder
Accessories: torque arm, result flange, output shaft, shrink disk, backstop device, protection cover kit, viton essential oil seals, reinforced result, assemble/disassemble kit
Series EP right angle helical bevel gear motors provide ratios from 8:1 to 160:1 in three phases or up to 10000:1 in five phases. Motors are available up to 90kW and output torque capability up to 12,300 Nm.
The series EP helical bevel gear motor is designed with integral cast feet for base or end mounting and can be offered with single or double extended output shafts.
Products are also available because shaft mounted or with result flanges and are designed for installation horizontally or vertically. The products can also be provided with a bolt on torque response bracket and all variants can be found either motorised or with an input shaft assembly.
Adding to the brand new range of Ever-Power helical gear motors the product takes advantage of our a long time of accumulated design expertise together with the utilization of top quality materials and parts. The outcome is a series of quickness reducing geared motors providing high load carrying capacities, increased efficiency, tranquil running and reliability.
Features of Helical Bevel Gear Motor
Standard motor connection
Ability to fit double oil seals, on input and output shaft since required.
All products are dimensionally interchangeable with other major manufacturers.
Units are manufactured and assembled from a family of modular kits for distributor friendliness minimizing inventory and maximizing availability.
Motorized units could be fitted with a backstop module and reducer Units can be fitted with a backstop and fan.
Applications:
-Conveyors, Agitators, Elevators, Cranes, Crushers
-Helical Bevel gear motors are found in industries such as chemicals, pharma, packaging, food processing, plastic material and automation etc.
Key Features:
Sizes: A40-A50-A70
Obtainable versions: EP – fitted for helical bevel gear reducer engine coupling, IEP – with input shaft, CEP – with small motor
Cases with foot, flange or universal
Switch on to 4,8 Kw
Gears with shaved or surface profile
Gearing with 2 and 3 reduction stages
Hypoid bevel gears for size A40 and A50, gleason bevel gear pairs for size A70, all with run-in profile
Reduction ratios between 7,62 and 442,76
Torque max 450 Nm and admissible radial loads max 5.500 N on hollow shaft and 10.000 N on solid shaft
Cases in die-cast aluminium alloy
Exceptional mechanical strength while being and particularly lightweight
Load capacity calculated to ISO6336 and verified according to AGMA 2001-B88
Painted with RAL 5010 blue epoxy-polyester powder in in accordance to DIN 1843
Accessories: torque arm, result flange, output shaft.
Generallntroduction of HK series:
Gear Reducer
The EP series gear units, are novel transmission gadget and composed of Y series electric motor, helical gear,Arc gear and worm gear. The gears are made from high wear-resisting alloy components, specifically and finely processed.
Advantages:
1: Helical-bevel equipment two-stage reducer
2: Compact framework, high efficiency
3: Quenched 20CrMnTi for gears
4: CE, ISO9001.
5: Compact design, small volume, fine appearance ,and strong capacity of being overloaded.
6: Precise division and wide selection for transmission ratio.
7: The performance is up to as high as 96% with low energy intake, strong adaptability and is capable of working continually in corrosive or damp environment.
8: All- purpose make use of, convenient and low-price maintenance.
9: New seal gadget, strong adaptability.
10: Varied range of motor combinations, mouting positions and struture projects.